Efecto generado por la presión calibrada en la estructura metalográfica y propiedades mecánicas del acero inoxidable austenítico 316L

Authors

DOI:

https://doi.org/10.15665/rp.v17i1.1825

Keywords:

316L, austenítico, SPD, GP, CGP, esfuerzos, microdureza.

Abstract

En este estudio, se evaluó el efecto de la técnica de presión calibrada, sobre las propiedades mecánicas y la microestructura de probetas de acero inoxidable AISI 316L, hasta lograr una deformación equivalente de ε~4,64. Dicha evaluación se realizó antes y después de aplicar la deformación plástica. Los resultados obtenidos mostraron un aumento en la dureza, el límite elástico y la resistencia útima a la tracción debido a la reducción del tamaño de grano, el maclado de mecánico y la transformación martensítica. 

Author Biographies

  • Erney Samir Jiménez Lora, University of Atlántico, Universidad del Atlántico
    EstudianteFacultad de IngenieríaPrograma de Ingeniería Mecánica
     Grupo de investigaciones CONFORMATUniversidad del Atlántico- Colombia
  • Breiner Antonio Fontalvo Gélvez, University of Atlántico, Universidad del Atlántico
    EstudianteFacultad de IngenieríaPrograma de Ingeniería Mecánica
     Grupo de investigaciones CONFORMATUniversidad del Atlántico- Colombia
  • OSCAR FABIÁN HIGUERA COBOS, University of Atlántico, Universidad del Atlántico
    Docente AsociadoFacultad de IngenieríaPrograma de Ingeniería Mecánica
    Director del Grupo de investigaciones CONFORMAT
    Universidad del Atlántico- Colombia
  • Isabel Cristina Niño Camacho, Centro Nacional Colombo Alemán-SENA

    Instructora G20 – Metalmecánica 

    Centro Nacional Colombo Alemán

    Investigadora Grupo de investigaciones CNCA-SENA

    Calle 30 No. 3e-164, Barranquilla, Colombia

  • Hugo Alexander Gonzalez Romero, Centro Nacional Colombo Alemán-SENA

    Profesional de Laboratorio - Servicios Tecnológicos

    Centro Nacional Colombo Alemán, Regional Atlántico

    Investigador Grupo de investigaciones CNCA-SENA

    Calle 30 N ° 3E - 164, Barranquilla, Colombia

References

A. Vinogradov and Y. Estrin, "Analytical and numerical approaches to modelling severe plastic deformation," Progress in Materials Science, vol. 95, pp. 172-242, 2018/06/01/ 2018.

S. S. Satheesh Kumar and T. Raghu, "Structural and mechanical behaviour of severe plastically deformed high purity aluminium sheets processed by constrained groove pressing technique," Materials & Design, vol. 57, pp. 114-120, May 2014.

R. Z. Valiev, Y. Estrin, Z. Horita, T. G. Langdon, M. J. Zechetbauer, and Y. T. Zhu, "Producing bulk ultrafine-grained materials by severe plastic deformation," JOM, vol. 58, pp. 33-39, April 01 2006.

S. S. Satheesh Kumar and T. Raghu, "Mechanical behaviour and microstructural evolution of constrained groove pressed nickel sheets," Journal of Materials Processing Technology, vol. 213, pp. 214-220, February 2013.

Z.-S. Wang, Y.-J. Guan, G.-C. Wang, and C.-K. Zhong, "Influences of die structure on constrained groove pressing of commercially pure Ni sheets," Journal of Materials Processing Technology, vol. 215, pp. 205-218, 2015/01/01 2015.

D. H. Shin, J.-J. Park, Y.-S. Kim, and K.-T. Park, "Constrained groove pressing and its application to grain refinement of aluminum," Materials Science and Engineering: A, vol. 328, pp. 98-103, May 2002.

E. Hosseini, M. Kazeminezhad, A. Mani, and E. Rafizadeh, "On the evolution of flow stress during constrained groove pressing of pure copper sheet," Computational Materials Science, vol. 45, pp. 855-859, 2009/06/01/ 2009.

M. Moradpour, F. Khodabakhshi, and H. Eskandari, "Dynamic strain aging behavior of an ultra-fine grained Al-Mg alloy (AA5052) processed via classical constrained groove pressing," Journal of Materials Research and Technology, 2018/06/30/ 2018.

F. Khodabakhshi, M. Kazeminezhad, and A. H. Kokabi, "Constrained groove pressing of low carbon steel: Nano-structure and mechanical properties," Materials Science and Engineering: A, vol. 527, pp. 4043-4049, 2010/06/25/ 2010.

M. Naghizadeh and H. Mirzadeh, "Modeling the kinetics of deformation-induced martensitic transformation in AISI 316 metastable austenitic stainless steel," Vacuum, vol. 157, pp. 243-248, 2018/11/01/ 2018.

S. J. Wang, T. Jozaghi, I. Karaman, R. Arroyave, and Y. I. Chumlyakov, "Hierarchical evolution and thermal stability of microstructure with deformation twins in 316 stainless steel," Materials Science and Engineering: A, vol. 694, pp. 121-131, 2017/05/10/ 2017.

A. Thirugnanam, T. S. Sampath Kumar, and U. Chakkingal, "Tailoring the bioactivity of commercially pure titanium by grain refinement using groove pressing," Materials Science and Engineering: C, vol. 30, pp. 203-208, 2010/01/01/ 2010.

F. Khodabakhshi, M. Abbaszadeh, H. Eskandari, and S. R. Mohebpour, "Application of CGP-cross route process for microstructure refinement and mechanical properties improvement in steel sheets," Journal of Manufacturing Processes, vol. 15, pp. 533-541, October 2013.

Downloads

Additional Files

Published

2019-04-04

Issue

Vol. 17 No. 1 (2019): Enero-Junio

Section

Articles

License

The authors to publish in this journal agree to the following conditions:

  1. The authors transfer the copyright and give the the journal first publication right of the work registered with Creative Commons Attribution License, which allows third parties to use the published work on the condition of always mentioning the authorship and first publication in this journal.
  2. The authors may perform other independent and additional contractual arrangements for the non-exclusive distribution of the version of the article published in this issue (E.g., Inclusion in an institutional repository or publication in a book), it must be indicated clearly that the work was first published in this journal.
  3. It allows and encourages the authors to publish their work online (eg institutional or personal pages) before and during the review and publication process. It can lead to productive exchanges and greater and faster dissemination of the published work (see The Effect of Open Access)

Instructions to fill out Certificate of Originality and Copyright Assignment

  1. Click here and get the forms of Certificate of Originality and Copyright Assignment  .
  2. In each field to fill out, click and complete the corresponding information.
  1. Once the fields are filled out, at the end of the form copy your scanned signature or digital signature. Please adjust the size of the signature on the form.
  2. Finally, you can save them as pdf files and send them through the OJS platform as an attachment.