Modelado, simulación y control de un reactor en la producción de cloruro de aluminio

Authors

DOI:

https://doi.org/10.15665/rp.v10i2.230

Keywords:

Control clásico, IAE, Cloruro de aluminio.

Abstract

El Cloruro de Aluminio es una sustancia importante como medio de transferencia de calor y como fluido de trabajo
en ciclos termodinámicos. Esta investigación consiste en la implementación de una estrategia de control clásico
sobre un proceso de producción de Cloruro de Aluminio a partir de materias primas recicladas. Las ecuaciones
diferenciales desarrolladas con base a los fenómenos fisicoquímicos que ocurren dentro del volumen de control
fueron suficientes para representar la dinámica del sistema y por tanto deducir la velocidad de respuesta y la
sensibilidad de este proceso.
Como indicador de la eficiencia del controlador evaluado para la simulación, se utilizó la integral absoluta del
error (IAE) teniendo en cuenta la dinámica del proceso. Los resultados de esta investigación demuestran que la
estrategia de control tiene buen desempeño para todas las situaciones estudiadas.

References

ITA, B. I., NSi M., and Simon, U.S., Corrosion inhibition

of aluminum in hydrochloric acid by 2-acetylpyridine

thiosemicarbazone derivatives, International Journal of

Natural and Applied Sciences (IJNAS),1(1), 73-80.

Narendra V., Matthew O., Frederick S. and Robert J.,

Mechanisms Of Elastin Calcification and its Prevention

With aluminum chloride pretreatment, Procedinlgs of The

First Joint BMES/EMBS Conference, 1999, Atlanta.

Yu, H., Fang, H., Tay, J., Enhanced Sludge Granulation

in Upflow Anaerobic Sludge Blanket (UASB) Reactors by

Aluminum Chloride, Chemosphere, 44, 31-36, 2001.

Christopher, J., Kenneth, P. I., Fredrick, W., Ray, E.,

Minhaal, K., Suffetd, I., Control of residual aluminum

from conventional treatment to improve reverse osmosis

performance, Desalination, 190, 147-160, 2006.

Denisov A., Morphological and Functional State of Major

Salivary Glands under Conditions of Aluminum Chloride

Excess in Drinking Water. Bulletin of Experimental

Biology and Medicine, 148, 703-706, 2009.

Wei, L., Li, Z., Chong, H., Qing, G., Yue S.,Yan, L., Effects

of Chronic Aluminum Exposure on the Collagen Metabolism

of Bone and Cartilage in Rats, 978-1-4244-4713-8/10.

Ghafari, S., Abdul H., Hasnain, M., Zinatizadehd, A.,

Application of response surface methodology (RSM) to

optimize coagulation–flocculation treatment of leachate

using poly-aluminum chloride (PAC) and alum, Journal

of Hazardous Materials, 163, 650-656, 2009.

Fengting, L., Jia-Qian, J., Shengju, W., Bingru, Z., Preparation

and performance of a high purity poly-aluminum

chloride, Chemical Engineering Journal, 156, 64-69, 2010.

Meiying, L. and Yongbo, S., High Efficiency Flocculation

Treatment of Gas Washing Wastewater from Iron and

Steel Plant, 978-1-61284-459-6/11.

Zhen, Z., Di, G., Liu, H., Li, X., Study on Industrial

Synthesis of Poly Aluminum Chloride and Coagulation

Effect with Different Basicities, 978-1-61284-340-7/11.

Liu, H., Di, G., Zhen, Z., Coagulants Optimization of

Low Turbidity Water Treatment in Feedwater Plant, 978-1-

-5089-3/11.

Downloads

Issue

Vol. 10 No. 2 (2012)

Section

Articles

License

The authors to publish in this journal agree to the following conditions:

  1. The authors transfer the copyright and give the the journal first publication right of the work registered with Creative Commons Attribution License, which allows third parties to use the published work on the condition of always mentioning the authorship and first publication in this journal.
  2. The authors may perform other independent and additional contractual arrangements for the non-exclusive distribution of the version of the article published in this issue (E.g., Inclusion in an institutional repository or publication in a book), it must be indicated clearly that the work was first published in this journal.
  3. It allows and encourages the authors to publish their work online (eg institutional or personal pages) before and during the review and publication process. It can lead to productive exchanges and greater and faster dissemination of the published work (see The Effect of Open Access)

Instructions to fill out Certificate of Originality and Copyright Assignment

  1. Click here and get the forms of Certificate of Originality and Copyright Assignment  .
  2. In each field to fill out, click and complete the corresponding information.
  1. Once the fields are filled out, at the end of the form copy your scanned signature or digital signature. Please adjust the size of the signature on the form.
  2. Finally, you can save them as pdf files and send them through the OJS platform as an attachment.